Mechanical power presses | Safeguarding for Specific Types of Machinery



Add a note hereAlthough there are three major types of power presses — mechanical, hydraulic, and pneumatic — the machinery that accounts for a large number of workplace amputations are mechanical power presses.
Add a note hereIn mechanical power presses, tools or dies are mounted on a slide, or ram, which operates in a controlled, reciprocating motion toward and away from the stationary bed or anvil containing the lower die. When the upper and lower dies press together on the workpiece, a re-formed piece is produced. Once the downstroke is completed, the re-formed workpiece is removed either automatically or manually, a new workpiece is fed into the die, and the process is repeated.

Figure 1: Two-hand control buttons on part-revolution clutch power press
Add a note here
Power press hazards
Add a note hereAmputations occurring from point of operation hazards are the most common types of injuries associated with mechanical power presses. Inadequate safeguarding allows the operators to inadvertently activate the power press tripping mechanism while their fingers are in the die (point of operation). For example, amputations can occur when an operator instinctively reaches into the point of operation to adjust a misaligned part or release a jam.
Add a note hereAmputations also occur when an operator’s normal feeding rhythm is interrupted, resulting in inadvertent placement of the operator’s hands in the point of operation. Such injuries typically happen while the operator is riding the foot pedal. Inadequate or ineffective safeguarding include:
§  Add a note hereGuards and devices disabled to increase production, to allow the insertion of small piece work, or to allow better viewing of the operation.
§  Add a note hereTwo-hand trips/controls bridged or tied down to allow initiation of the press cycle using only one hand.
§  Add a note hereDevices such as pullbacks or restraints improperly adjusted to fit the specific operator.
§  Add a note hereControls of a single-operator press bypassed by having a coworker activate the controls while the operator positions or aligns parts in the die, or repairs or troubleshoots the press.
§  Add a note hereFailure to properly lockout/tagout presses or to have a special method in place for making adjustments, clearing jams, performing maintenance, installing or aligning dies, or cleaning the machine.
Add a note hereSome amputations are linked to machine failure, such as failure of a single-stroke linkage resulting in a “double cycle,” electronic failure of two-hand controls, brake failure resulting in the slide falling, and jammed relays in light curtains.
Power press safeguards
Add a note hereMechanical power presses are extremely versatile, and selecting appropriate safeguarding methods depends on the specific press design and use. You should consider the press, the type of clutch used, the stock size, the length of production runs, and the method of feeding.
Add a note hereYou can use engineering controls such as guards to prevent injuries. For example, §1910.217 requires employers to provide and ensure the use of point of operation guards or properly installed devices on every operation performed on a press when the die opening is greater than 1/4 inch. If the dies of a power press can be adjusted so that they never open more than 1/4 inch, there is no need for a point of operation guard. This is referred to as “stroke limitation” and is a good choice when practical.
Add a note hereIn addition, guards must conform to the maximum permissible openings of Table O-10 of §1910.217. Guards must prevent entry of hands or fingers into the point of operation through, over, under, or around the guard.

Case History 
Add a note hereWhile using an unguarded, foot pedal-operated, full-revolution mechanical power press that made trip collars for wood stoves, an employee used his hands to feed and remove finished parts and scrap metal. He placed the completed part to the left side of the press, then turned to place the scrap in the bin behind him. As he turned back to face the press, he inadvertently stepped on the foot pedal and activated the press while his hand was in the die area. His left hand was amputated at the wrist.
Work practices and administrative controls
Add a note hereThe types of work practices and administrative controls you provide can make a big difference in reducing the potential for amputation hazards. For example, if workers operate presses under a “no hands in die” policy using feeding methods such as hand-tool feeding, safeguarding (two-hand trip, Type A and B gates, or presence-sensing device) you still must protect operators. Hand-tool feeding alone does not ensure that the operator’s hands cannot reach the danger area. (Figure 2 illustrates the use of hand feeding tools in conjunction with pullbacks on a power press.)


Figure 2: Hand feeding tools used in conjuction with pullbacks on a power press
Add a note here
Add a note hereRemoving scrap or stuck work with tools is required even when hand feeding is allowed according to §1910.217(d)(1)(ii). You must furnish and enforce the use of hand tools for freeing or removing work or scrap pieces from the die to reduce the amount of time an operator’s hand is near the point of operation.
Add a note hereIn addition, work practices such as regular mechanical power press inspection, maintenance, recordkeeping, and reporting are essential.
§  Add a note here§1910.217(e)(1)(i) requires a program of periodic and regular inspections of mechanical power presses. You must inspect and test the condition of the clutch/brake mechanism, antirepeat feature, and single-stroke mechanism and maintain records of these inspections and the maintenance performed.
§  Add a note here§1910.217(g), requires the reporting of all point of operation injuries within 30 days to OSHA.
Goals for power press point of operation safeguards
1.  Add a note herePrevent or stop the normal press stroke if the operator’s hands are in the point of operation; or
2.  Add a note herePrevent the operator from reaching into the point of operation as the die closes; or
3.  Add a note hereWithdraw the operator’s hands if inadvertently placed in the point of operation as the die closes; or
4.  Add a note herePrevent the operator from reaching the point of operation at any time; or
5.  Add a note hereRequire the operator to use both hands for the machine controls that are located at such a distance that the slide completes the downward travel or stops before the operator can reach into the point of operation; or
6.  Add a note hereEnclose the point of operation before a press stroke can be started to prevent the operator from reaching into the danger area before die closure or enclose the point of operation prior to cessation of the slide motion during the downward stroke.
Other controls for die set-up and maintenance
Add a note hereAdditional controls pertaining to mechanical power press die set-up and maintenance include the following:
§  Add a note hereControl point of operation hazards created when guards are removed for set-up and repair by operating the machine in the inch mode. This involves using two-hand controls to gradually inch the press through a stroke when the dies are being tested on part-revolution clutch presses.
§  Add a note hereAvoid making machine repairs or modifications while the machine can be stroked.
§  Add a note herePrevent stroking by using die blocks or interlocked barrier guards.
§  Add a note hereDisconnect or remove foot controls while die work is being performed if they are used to initiate the stroke.
Training
Add a note hereTraining is essential for worker protection. As an employer, you should train operators in safe mechanical press operation procedures and techniques before they begin work on the press. Additionally, supervise operators to ensure that correct procedures and techniques are being followed.

No comments:

Popular Posts